PiezoPressureSensor.
Menu

PPS-BLT-BAL · CONFIGURATION REVIEW

Ultra-High-Pressure & Ballistic Chamber Transducers

Define a chamber-pressure measurement by its range, pulse shape, sealing geometry and conditioning. A requested envelope to 700 MPa is reviewed per configuration; it is not a rating of every sensor in this family.

Specify this configuration ↘

Technical content reviewed 16 November 2026 · PiezoPressureSensor

Ultra-High-Pressure & Ballistic Chamber Transducers: sensing and signal-path concept
Original engineering concept; configuration-specific product drawings are reviewed separately.

REQUEST A CONFIGURATION / PPS SERIES

Select the signal and installation you need.

PPS codes below identify inquiry families. The table defines what to review; it does not assign an unverified pressure, temperature or bandwidth rating to a supplied unit.

Configuration families and acceptance checks
Configuration requestPressure / taskElectrical chainInstallation reviewNext step
PPS-BLT-BALHigh-pressure chamber requestApplication envelope up to 700 MPa requested; not a released ratingCharge or IEPE selected against signal headroomRange vs proof/burst, pulse fatigue, port and protective assemblyKistler 6215 / original ballistic modelRequest this family ↘

01 / ENGINEERING NOTES

Use the same units and the same pressure reference

1 MPa = 10 bar ≈145.038 psi. A 600 MPa requirement is 6,000 bar / about 87,023 psi; 700 MPa is about 101,526 psi. A 100,000 psi requirement is about 689.5 MPa. Keep gauge, absolute or differential reference beside the value.

02 / ENGINEERING NOTES

Range, survival and repeated pulses are separate

A sensing element can survive a transient outside its calibrated range without producing an accurate waveform there. Review peak dynamic range, static preload, proof/burst evidence, cycle count and the requested uncertainty independently.

  • Supply pulse duration and repetition; include any long plateau or negative phase.
  • Identify incident or reflected loading where relevant.
  • Specify permitted zero shift, repeatability and response error rather than assuming a survivable pulse is measurable.

03 / ENGINEERING NOTES

Front seals and clamp mounts need the original drawing

Match the diaphragm location, mechanical thread, sealing surface and cable routing to the exact original configuration. The electrical connector designation is not the pressure-port thread. A generic pipe adapter is not a qualified ultra-high-pressure installation.

  • Provide the original model suffix and current port drawing through the private attachment field.
  • Confirm seal material, engagement, installation instructions and pressure-rated assembly evidence.
  • Protective coatings or screens require response review with the actual assembly.

04 / ENGINEERING NOTES

Select charge or IEPE against voltage and charge headroom

A charge-output chain must stay within amplifier input charge and output swing; an IEPE chain must meet current, bias, cable drive and recorder voltage limits. Sensitivity and gain must avoid clipping at the largest requested excursion.

05 / ENGINEERING NOTES

Treat an original-model listing as a review input

The official Kistler 6215 page describes a 6,000 bar quartz model and its original AEP-97 listing. Those facts do not qualify a PPS equivalent. Any proposed assembly needs its own rated range, dimensional acceptance and calibration documents.

ORIGINAL-MODEL DATA / INDEPENDENT REVIEW

Keep original specifications separate from a proposed replacement.

Facts below describe the named original models. A PPS configuration still needs its own dimensional, electrical and calibration evidence. Resonance and flat bandwidth are different quantities.

Original reference facts checked 16 November 2026
Original model & sourceVerified reference factsCompatibility checkReview request
PCB Piezotronics 113B225,000 psi / 344.7 bar; 1 mV/psi; resonance ≥500 kHz; rise time ≤1 μs.The range is for ±5 V output. Resonance is not flat bandwidth. Mounting uses a separate floating clamp nut; electrical 10-32 is not a pressure-port thread.Review this original ↘
Kistler 6215Quartz; 6,000 bar / 600 MPa / about 87,023 psi; M10 front seal.6000 bar = 600 MPa nominal; do not call this a 700 MPa model or transfer AEP listing to PPS.Review this original ↘

No affiliation or universal interchangeability is implied. Pressure-port threads and electrical connector threads must be checked separately.

Source-model evidence and sensing principle

The Y1004E supplier photograph identifies a 0–100 MPa IEPE reference. It does not establish a 700 MPa PPS configuration or ballistic qualification.

SOURCE-DOCUMENTED HARDWARE REFERENCES

Review the package and its sensing principle.

These supplier-reference images show the indicated arrangements. Final pressure, medium, dimensional and response requirements are confirmed for the proposed configuration.

High-range IEPE dynamic pressure-sensor reference.
IEPE high-range pressure reference — source 0–100 MPaEdited supplier photographic reference · source Y1004ESource model & documentation ↗

AT THE PRESSURE PORT

The installed passage changes the recorded event.

Concept comparison of a recessed gas passage and a diaphragm aligned to the local wall, with sealing location shown
Concept only. Actual diaphragm position, thread engagement, seal and pressure rating require the installation drawing.

A recess adds an acoustic system.

A small cavity and connecting passage can add amplitude peaking, ringing and delay. A tapered pipe thread does not set a reproducible diaphragm depth.

Flush alignment needs dimensions.

Match the front face, sealing shoulder, gasket compression and allowed protrusion/recess. A protection layer or screen also belongs in the installed response review.

Review cavity models & thermal protection ↗

Pressure-chain questions for this configuration

Does an original AEP listing transfer to an alternative sensor?

No. Original-model references describe the named original only. Qualification, range, installation and documentation need review for the proposed configuration.

Are 700 MPa and 100,000 psi identical?

No. They are close rounded market descriptions with different numerical values. Use the exact required rating and reference in the RFQ.

Sources and scope of the comparison

Original-model facts and general methods describe their named sources. They do not qualify a PPS unit or imply manufacturer affiliation.

COMPLETE THE PRESSURE MEASUREMENT CHAIN

Specify conditioning, mounting and protection together.

Optional budget requests. Confirm the input type, response, channel count and installed compatibility. Specialist hydrophone preamplifiers, hot-zone hardline cables and cooled assemblies are quoted separately.

Review selected configuration ↘

PREPARE A REVIEWABLE BRIEF

Download the worksheets for your project.

These are blank engineering request/checklist documents. They are not released product datasheets, calibration certificates or signed quotations.

ENGINEERING RFQ / PPS-BLT-BAL · CONFIGURATION REVIEW

Send this pressure configuration for review.

Include the original suffix and a private installation drawing when available. Final specifications, evidence, price and lead time are confirmed in writing.

PPS-BLT-BAL

Pressure event & project contact
Document package requested

Optional requests for the exact offered assembly. Availability, scope and approval are confirmed during quotation.

Accessory requests for this chain

Opt in to the items you need. These are budget requests; compatibility, channel count and final price require review.

Bring the whole pressure event into focus.

Discuss your application ↗